Owner / Builder and Permit Ready Swimming Pool Plans

We offer both “PERMIT READY“, as well as “OWNER BUILDER” design services for those who wish to engage the “do-it-yourself” approach.

Swimming Pool Layout

What is a Permit Ready Plan…?

This level of planning is focused upon expressing the current Building Code Requirements , diagrammatic exhibits, specifications and other information that are mandated by the Building Department to be represented on a plan for submission in the pursuit of obtaining the official regulator agency’s permission to build.

What is an Owner Builder plan…?

This level of planning can provide an advancing focus for providing building directions that go beyond the basic code compliance requirements and common practices.

Industry standards are not so standard in the swimming pool industry, and as such the simplicity of strictly adhering to just a code compliant installation may leave an installer to make assumptions for the desired objectives in the installation practices.

If an Owner wishes to orchestrate the construction with a much more definitive result in mind, then this is the level of planning that should be considered. The Owner Builder level of planning illustrates much of the time tested experience that comes form our generationally acquired construction experience.

The difference being between the two levels of planning is the time invested in producing the additional planning sheets listed and explained below as Advance Design Assistance.

Advance Design Assistance

Other planning sheets (not required for permit purposes) are also available, which can involve exhibiting a deeper meaning of understanding in order to articulate a more definitive instruction to performing sub-contractors.

Our Owner / Builder Plans provide you with a complete equipment listing of all the manufacturers, model numbers and sizes that can call-out over one-hundred items, which may pertain to specifying your job done correctly!

Equipment Listing

Click on the image below to open, click twice to enlarge view …

Equipment Listing

As part of our design efforts, we indicate everything in great “DETAIL” that will be necessary, from the electrical wire-up for a sub-panel to the gas pipe size for a heater.

We organize the “DETAILS” that are pertinent as being 1 thru 82. These numbering assignments are then referenced on the plans as to where each will apply. See the Detail Listing below for the descriptions that allow you to fully understand how to achieve a 1st Class standard from a great set of plans!

Equipment Listing

Click on the image below to open, click twice to enlarge view …

Construction Detail Listing

Such instructions can be desired by a Homeowner who wishes to reduce independent interpretations by performers and provide a mechanism for authenticating the original intentions being desired for the installation standards.

If you wish to view a 3-miniute YouTube clip about the differences between PERMIT READY vs OWNER BUILDER, just click upon the image below. When complete use your Browser’s “BACK ARROW to return to this page.

PLEASE SCROLL DOWN TO COMPLETE OUR WEB-FORM QUESTIONNAIRE, THANK YOU!


Residential Design Request for Information (RFI)

Maximum file size: 31.46MB

IF YOU CAN PROVIDE A ROUGH SKETCH OF YOUR IDEAS, TOGETHER WITH THE BASIC DIMENSIONS OF THE LAYOUT, THIS SHALL AID THE PROCESS FOR GETTING OUR MIND AROUND YOUR DESIRED CONCEPT.

Maximum file size: 31.46MB

PLEASE PROVIDE US WITH AN OFFICIAL PROPERTY PLOT PLAN THAT IS SHOWING ALL PROPERTY LINE DIMENSIONS.

Maximum file size: 31.46MB

UPLOAD AN IMAGE FILE HERE OF ANY IMAGE LIKENESS THAT CAN BETTER EXPLAIN YOUR DESIRES

Maximum file size: 31.46MB

UPLOAD AN IMAGE FILE HERE OF ANY IMAGE LIKENESS THAT CAN BETTER EXPLAIN YOUR DESIRES
First
Last
Project Address
City
State/Province
Zip/Postal
Country
PROVIDE THE PROJECT ADDRESS
PROVIDE US WITH A LIST OF YOUR "MUST HAVE" ELEMENTS OF DESIRE I.E., POOL, SPA, CABO SHELF, WATER FEATURE, FIRE PIT, ETC...
WE CAN PROVIDE TWO DIFFERENT LEVELS OF DESIGN SERVICE. AS EXPLAINED ON THE PAGE ABOVE THIS WILL INVOLVE MORE OR LESS PLANNING SHEETS. PLEASE SELECT THE LEVEL THAT BEST SUITS YOUR DESIRES FOR INFORMATION.
THESE ARE THE FIVE (5) MAJOR POOL EQUIPMENT MANUFACTURERS. WE RECOMMEND "PENTAIR" AS WE BELIEVE THAT HAVE THE BEST PRODUCT WARRANTY SERVICE SUPPORT NATIONWIDE
MOST BUILDING DEPT.'S SHALL REQUIRE STRUCTURAL ENGINEERING, AS ONE OF THE PREREQUISITES FOR OBTAINING A PERMIT TO BUILD. IF A PROJECT HAS UNIQUE FEATURES (WATERFALL, SITE RETAINING WALLS, ETC.) THEN THE STANDARD "BOILER PLATE" WOULD NOT SUFFICE AND A "SITE SPECIFIC" WOULD NEED TO BE PROVIDED IN ORDER TO ADDRESS THE CONSTRUCTION APPROACH FOR ANY SPECIALITY FEATURES.
STRUCTURAL ENGINEERING CAN INVOLVE A STANDARD APPROACH TO THE EXISTING CONDITIONS WHICH ANTICIPATES NORMAL OR EXPANSIVE LOAD VALUES FOR THE IMPOSING SOIL PRESSURES. IF THE EXISTING CONDITIONS AND OR OTHER CONSIDERATIONS FALL OUTSIDE THIS CRITERIA FOR THESE STANDARDS, THEN "SITE SPECIFIC" STRUCTURAL ENGINEERING CONSIDERATIONS MUST EVALUATE THE UNIQUENESS OF THE SITE'S GEOTECHNICAL CONDITIONS AND CONSIDER A STRUCTURAL REMEDY THAT CAN ACCOMMODATE THE DESIGN. IF A "SITE SPECIFIC" APPROACH BECOMES NECESSARY, THEN THE SUBMISSION OF A "PLOT PLAN" MUST BE ACCOMPANIED WITH A CURRENT SOILS REPORT (CERTIFIED WITHIN PAST 2-YEARS).
PROVIDE THE DESIRED MEASUREMENTS FOR THE LENGTH & WIDTH OF THE POOL.
PROVIDE THE DESIRED MEASUREMENTS FOR THE SHALLOW AND DEEP END OF THE POOL.
SELECT A POOL SHAPE / STYLE
IF YOU DESIRE A SHALLOW AREA THAT IS REFEREED TO AS A "CABO SHELF" AND OR "CARIBBEAN SHELF" SELECT THE DESIRED DEPTH ABOVE. ALSO, REMEMBER THAT THE DEPTH IS MEASURED FROM THE "FINISHED CONCRETE" DECK ELEVATION, NOT THE ACTUAL WATER DEPTH. THE DECK IS TYPICALLY +5 TO +6" ABOVE THE POOL WATER SURFACE. THUS A -18" DEPTH WOULD REPRESENT APPROXIMATELY -12" OF ACTUAL WATER DEPTH.
IN YOUR ROUGH SKETCH YOUR POOL / SPA DESIRES, TOGETHER WITH THE GENERAL DESCRIPTION FOR THE OVER ALL LENGTH AND WIDTH
IF YOU DESIRE A BENCH THAT IS REFEREED TO AS A "SWIM-OUT" SELECT THE DESIRED DEPTH THAT YOU WOULD LIKE TO SEE. REMEMBER THAT THE DEPTH IS MEASURED FROM THE "FINISHED CONCRETE" DECK ELEVATION, NOT THE ACTUAL WATER DEPTH. THE DECK IS TYPICALLY +5 TO +6" ABOVE THE POOL WATER SURFACE. THUS A -18" DEPTH WOULD REPRESENT APPROXIMATELY -12" OF ACTUAL WATER DEPTH.
A TYPICAL BENCH WOULD BE APPROXIMATELY 6'-0" LONG. THESE CAN BE PLACED UNDER A WATERFALL AND ACT AS A SEAT, AS WELL THEY CAN ACT AS AN ENTRY OR EGRESS POINT FOR GETTING IN AND OUT OF THE POOL'S ENVIRONMENT.
CLICK "YES" IF YOU DESIRE AN IN-GROUND SPA AS PART OF YOUR POOL'S CONCEPT
IN-GROUND SPAS CAN TAKE VIRTUALLY ANY SHAPE AND STARTING WITH A SHAPE CAN HELP US TO BETTER ENVISION WHAT YOU ARE GRAVITATING TOWARD. FROM THE SHAPE WE CAN PROPORTIONALITY DIMENSION THE SPA IN RELATION TO THE POOL AND YARD SPACE THAT IS AVAILABLE. AS WELL, THE NUMBER OF SEATING POSITIONS BEING DESIRED SHALL DICTATE THE SPA'S SIZE AND SHAPE.
IN CALLING OUT THE SPA'S DIMENSIONS, TAKE A PAD AND PEN AND SKETCH A SELECTED SHAPE AND THEN USE A MINIMUM SPACING DISTANCE BETWEEN EACH SEAT OF 3'-0". THIS OF COURSE IS THE MINIMUM AND IF YOU'LL HAVE LARGER ADULTS GENERALLY USING THE SPA, THEN YOU'LL NEED TO ACCOMMODATE A WIDER SEATING AREA. FROM THIS RESULT YOU'LL BE ABLE TO BETTER IMAGINE THE SPA'S USAGE AND CAPACITY. ALSO REMEMBER THAT LARGE SPA'S HOLD MORE WATER AND SHALL REQUIRE MORE TIME TO BRING UP TO THE HEATED TEMP.
DEPENDING UPON THE TORSO MEASUREMENT (FROM BASE OF SPINE TO BOTTOM OF CHIN), THE DESIGNATED DEPTH OF THE SPA'S SEAT CAN BE DETERMINED. SEATING CAN BE VARIED AND GENERALLY WILL RANGE BETWEEN -18" TO -20" OF WATER DEPTH, YOU'D BE ADDING +5" TO 6" TO THIS MEASUREMENT IN USE THE COMMON REFERENCING FROM DECK HEIGHT. THE SPA DEPTH IS REFERRING TO THE SPA'S VERY BOTTOM AND AGAIN...THE DEEPER THE SPA THE MORE WATER AND MORE TIME TO HEAT UP. TYPICALLY, A 3'-0" (-36") WATER DEPTH IS IDEAL.
THE DESIRED SEATING POSITIONS WILL DICTATE HOW MANY JETS WILL SUFFICE. THE NUMBER OF JETS PER SEATING POSITION, TIMES THE NUMBER OF SEATS WILL QUANTIFY THE TOTAL NUMBER OF JETS NECESSARY. IMAGINE YOU'RE ACTUALLY IN THE SEAT AND THINK ABOUT WHERE YOU WANT THE JET ACTION TO COME IN CONTACT WITH YOUR BODY. THESE THERAPEUTIC PRESSURE POINTS CAN ADD TO THE RELAXING AND SOOTHING COMBINATION FOR ENJOYMENT. THERE IS A MANIFOLD STYLE OF JET CONFORMITY THAT CAN POSITION 3-JETS ON THE BACK REST PORTION OF THE SPA'S SEATING POSITION. THESE CAN BE INSTALLED AS ONE ON THE LOWER BACK AND TWO ON THE UPPER OR REVERSED, AS TWO ON THE LOWER AND ONE ON THE UPPER. THIS CAN BE COMPLIMENTED WITH ANOTHER SINGLE JET POSITIONED BEHIND THE CALF OF THE LEG. THIS OVERALL JET CONFORMITY WOULD THEN REQUIRE FOUR JETS PER SEATING POSITION. THE MAXIMUM NUMBER OF JETS PER 3-HP BOOSTER PUMP IS +/- 12-EA. THUS FOUR JETS TIMES 3-SEATS WOULD EQUAL THE 12-EA MAXIMUM FOR A SINGLE BOOSTER PUMP (SEE MORE ABOUT HP / JET NOZZLES BELOW). IF MORE JETS OR SEATING POSITIONS ARE DESIRED THEN ANOTHER BOOSTER PUMP MAY BE REQUIRED.
IN-GROUND SPAS CAN RANGE FROM A TUB OF HOT WATER TO A HYDROTHERAPY LEVEL OF JET ACTION THAT WILL SOOTH AND RELAX A CONDITIONED ATHLETIC BODY. ON A 1 TO 10 SCORING, SELECT THE LEVEL OF SOPHISTICATION EXPECTED BY THE RESULTS OF BUILDING AN IN-GROUND SPA. THE REFERENCE TO "AIR" ABOVE IS REFERRING TO A DEVICE CALLED AN "AIR BLOWER" AND DEPENDING UPON THE SELECTED NUMBER OF JETS, IT MAY REQUIRE UTILIZING A DUAL PUMPING AND A DUAL AIR BLOWER SYSTEM.
FOR SOME FOLKS, THE JETS ARE NOT REALLY IMPORTANT, AS THEY JUST WANT TO RELAX IN THE HOT WATER ENVIRONMENT. IF THIS IS THE CASE THEN A BOOSTER PUMP MAY NOT BE NECESSARY AND THE SPA'S FILTRATION PUMP WOULD AID THE JET'S FUNCTION. THIS WOULD GENERALLY ALLOW UP TO SIX SINGLE JETS (ONE PER SEATING POSITION) TO BE OPERATIONAL WHILE FILTERING / HEATING THE SPA. THIS IS A SIMPLER WAY TO BUILD A SPA. THE DOWN SIDE IS THAT IT TAKES LONGER TO HEAT THE SPA UP BECAUSE THE SPA JETS ARE A VENTURI TYPE JET THAT ALSO INDUCES AIR. COLDER AIR BEING MIXED WITH WATER BEING WARMED UP COOLS THE WATER DOWN AS IT PASSES THROUGH THE JET, THUS TAKING LONGER TO HEAT THE WATER. THIS IS ONE OF THE MAIN REASONS THAT MANY LESS SOPHISTICATED APPROACHES TO BUILDING IN-GROUND SPAS RESULTS IN TAKING TOO LONG TO HEAT UP.
AN AIR BLOWER IS AN OPTION AND IF A BOOSTER PUMP ISN'T UTILIZED THEN AN AIR BLOWER'S CONTRIBUTIONS ARE SOMEWHAT NEGATED. WHEN INSTALLED IN COMBINATION WITH A BOOSTER PUMP THE AIR BLOWER ACTS AS A SEPARATE THERAPEUTIC POSSIBILITY AND CAN BE ACTIVATED AS AN AUTOMATED RELAY FUNCTION FOR THE SPA'S EXTENDED OPERATIONAL ENJOYMENT. THE WAY THE AIR BLOWER WORKS UNDER THIS SPECIFICATION IS THAT WHEN THE VENTURI STYLE JET'S FORCED WATER IS PASSING THRU THE JET THE BLOWER PROVIDES A HIGHER CUBIC FOOT PER MINUTE (CFM) AIR VOLUME THAN WHAT WOULD OTHERWISE BE AVAILABLE UNDER JUST THE NORMAL INDUCTION PERFORMANCE OF THE VENTURI EFFECTS. THEREFORE, THERE IS MORE AIR AVAILABLE AT THE JET'S VENTURI ORIFICE PROVIDING FOR BETTER AIR / JET ACTION "BUBBLES". THESE BUBBLES TOGETHER WITH THE WATER STREAM PROVIDE A PULSATING EFFECT THAT MIMICS A MESSAGE FOR APPLY A VARIATION IN RESPONDING PRESSURE BEING APPLIED TO THE BODY.
WHEN HEATING A POOL OR SPA IT IS 67% MORE EFFICIENT TO DELIVER THE HEATED WATER TO THE BOTTOM OF THE WATER'S ENVIRONMENT. THIS IS SUBSTANTIATED IN THE SCIENCE OF HYDRONICS AND SOME OF THE OLDEST EXAMPLES OF THIS ARE STEAM AND HOT WATER RADIATORS. IN PROVIDING A PLUMBING DESIGN THAT TAKES ADVANTAGE OF THIS, THE WATER WILL HEAT UP FASTER AND MORE EFFICIENTLY. HOT WATER RETURNS ARE GENERALLY CONNECTED TO AN AUTOMATED FUNCTION FEATURE THAT CAN ACTIVATE THIS MODE OF OPERATION WHEN IT IS BEING DESIRED.
LIGHTING IS VERY IMPORTANT FOR EXTENDING THE HOURS OF OPERATIONAL ENJOYMENT OF THE POOL'S ENVIRONMENT. BESIDES SAFETY DURING NIGHT-TIME USE, TAKING ADVANTAGE OF COLORED LIGHTING CAN HEIGHTEN THE VISUAL EFFECTS WHILE HIGHLIGHTING THE ASCETIC ATTRIBUTES OF A BACKYARD'S LIVING SPACE. A POOL / SPA ISN'T JUST FOR SWIMMING, IT CAN ALSO PROVIDE THE VISUAL APPEAL DURING OFF-SEASON.
THE NUMBER OF LIGHTS NECESSARY WILL HAVE TO DO WITH THE SIZE OF THE POOL / SPA AND THE TYPE OF LIGHT SELECTED. THE LATEST STYLE OF LIGHT (GLO-BRITE 12v) HAS A SMALLER FACE AND NO LONGER REQUIRES THE LARGE CANISTER NICHE TO BE INSTALLED, THEREFORE MAKING THEM LESS EXPENSIVE PER LIGHT TO INSTALL. AS A LOW VOLTAGE LIGHT THESE ARE INCREDIBLY ENERGY EFFICIENT AND QUITE BRIGHT (190-WATT EQUIVALENCE) FOR THE AMOUNT OF POWER BEING USED. ALTHOUGH MORE LIGHTS MAY BE USED, THE BENEFIT IS THAT THE LIGHT DISTRIBUTION CAN BE BETTER PIN POINTED TO ACHIEVE A MORE COMPREHENSIVE RESULT FOR THE ILLUMINATING EFFECTS. THIS MEANS UNDER LIGHTING WATERFALLS FROM BENCHES, PROVIDING LIGHTS AT THE ENTRY STEPS AND OTHER POINTS OF ENTRY, AS WELL AS DESIGNATING A FIXED COLOR (WHITE, BLUE, MAGENTA, GREEN) AND OR CHANGING COLORS THROUGH THE AUTOMATION SYSTEM'S PROGRAMMABLE CONTROL FUNCTION FEATURES.
A TYPICAL SPA WOULD UTILIZE A SINGLE LIGHT. IF THE SPA IS A UNIQUE SHAPE AND OR LARGER YOU MAY WISH TO CONSIDER ADDITIONAL LIGHTING.
SURFACE SKIMMERS ARE FOR THE PURPOSE OF DRAWING FLOATING DEBRIS INTO THE THROAT OF THE SKIMMER DEVICE AND DEPOSITING THIS DEBRIS INTO A BASKET THAT REST INSIDE THE SKIMMER'S CANISTER. WHEN THESE ARE POSITIONED IN A MANNER THAT TAKES ADVANTAGE OF THE "RETURN LINES" COUNTER-ROTATION DIRECTIONAL ADJUSTED INLETS, THEN IT SHALL GREATLY REDUCE THE AMOUNT OF DEBRIS THAT ENDS UP ON THE BOTTOM OF THE POOL / SPA. THE DESIGN OF ANY POOL / SPA SHOULD INVOLVE CONSIDERATIONS FOR THE EASE OF MAINTENANCE OPERATIONS AND THE PLACEMENTS OF THIS SUCTION SIDE DEVICE IS AN IMPORTANT PART OF THOSE CONSIDERATIONS. GENERALLY SPEAKING A SKIMMER RATIO WOULD BE 1-SKIMMER PER EVERY 500-SF OF POOL SURFACE AREA.
WATER FEATURES COME IN ALL SHAPES AND SIZES BUT BEGINNING WITH A DIMENSIONAL RELEVANCE CAN HELP TO START THE PROCESS AND DEFINING THE ATRIBUTES.
DEPENDING UPON THE TYPE, STYLE AND SIZE OF A WATER FEATURE, THE QUANTITY OF LIGHTS CAN VARY. WHEN ENVISIONING HOW YOU'D LIKE TO ILLUMINATE THE FEATURE WILL HELP TO QUANTIFY THE AMOUNT OF LIGHTS THAT MAY BE NECESSARY. LIGHTS SHOULD GENERALLY BE PLACED SO THAT THEY SHINE AWAY FROM THE HOME OR VIEWING LOCATION'S VANTAGE POINT IN A FASHION THAT PLACES THE LIGHT IN A LOCATION THAT CAN ESCAPE SEEING THE ACTUAL LIGHTING FIXTURE.
THERE ARE MANY "SPECIAL FEATURE" POSSIBILITIES THAT CAN PROVIDE ENHANCEMENTS TO THE OVERALL ENJOYMENT, ABOVE ARE A FEW TO SELECT FROM
IN SELECTING A FILTER, IT IS IMPORTANT TO CONSIDER WHAT COSTS MORE TO MAINTAIN. CARTRIDGES MUST BE REPLACED EVERY 18 TO 24 MONTHS (ACCORDING TO THE MFG.'S RECOMMENDATIONS) AND REPLACEMENTS SHALL RUN $400 TO $600 FOR EVERY TIME YOU REPLACE THEM. ADDITIONALLY, CARTRIDGE AND D.E. FILTERS WILL FILTER DOWN TO 5 MICRON AT CLEAN STAGE AND 2-3 MICRON AT DIRTY STAGE. THIS LEVEL OF FILTRATION IS TRULY OVER FILTRATION FOR A SWIMMING POOL AND ADDS TO THE OVERALL TDH RESTRICTION FOR THE SYSTEM (RESTRICTION = LOST ENERGY), MAKING PUMPS WORK HARDER AND LESS EFFICIENT. FURTHER MORE, THE HUMAN EYE CANNOT DISTINGUISH A PARTICLE SIZE SUSPENDED IN WATER BELOW 40 MICRONS. REALIZE THAT SAND FILTRATION AT CLEAN STAGE STARTS AT 20 MICRON AND GETS TO 10 MICRONS AT THE DIRTY STAGE, THAT'S FOUR TIMES SMALLER THAN THE NAKED HUMAN CAN SEE! WHEN TALKING TO YOUR SOLICITED PLUMBERS SEE IF THEY UNDERSTAND THIS CONCEPT AND CHOOSE A PERFORMER WHO DOES.
THE INTELLIFLO VARIABLE FLOW (VSF) PUMP PROVIDES PRECISE FLOW CONTROL, WHICH MEANS INCREASED EFFICIENCY, SAVINGS AND PERFORMANCE. THE PUMP’S INNOVATIVE DUAL-TECHNOLOGY DESIGN ENSURES THE DESIRED FLOW RATE IS MAINTAINED, NO MATTER THE CONDITIONS. PLUS, THE INTELLIFLO VSF PUMP HELPS THE REST OF YOUR EQUIPMENT PERFORM EXACTLY AS IT’S MEANT TO—FROM FILTERS TO LAMINARS TO WATERFALLS. THE INTELLIFLO VSF VARIABLE SPEED AND FLOW PUMP IS JUST ANOTHER IN A LONG LINE OF INNOVATIVE PRODUCTS FROM PENTAIR.
SCRUBS AND VACUUMS AWAY THE TOUGHEST DIRT AND THE "SUCTION SIDE" KREEPY KRAULY GREAT WHITE CLEANER’S BRISTLE-DRIVE™ TECHNOLOGY HAS THE STRENGTH TO KNOCK LOOSE THE MOST STUBBORN DIRT, WHILE THE POWERFUL VACUUM ACTION WHISKS AWAY SMALL AND LARGE DEBRIS. ITS 15-IN.-WIDE PATH AND PROGRAMMED STEERING GET THE CLEANING JOB DONE QUICKLY. • BRISTLES DISLODGE TOUGH DIRT • OVERSIZED VACUUM INLET CAPTURES LARGE DEBRIS • SMARTTRAC PROGRAMMED STEERING EASILY NAVIGATES AROUND POOL OBSTACLES FOR UNINTERRUPTED CLEANING • ADJUSTABLE TO ENSURE THE MOST EFFECTIVE CLEANING
CLASSIC WHITE STANDARD WHITE PLASTER IS THE TRIED AND TRUE POOL AND SPA SURFACE FINISH. WHITE PLASTER HAS BEEN AROUND AS LONG AS PEOPLE HAVE BEEN BUILDING SWIMMING POOLS AND IT REMAINS A POPULAR CHOICE IN SPITE OF THE MYRIAD OF CHOICES THAT HAVE COME INTO THE MARKET IN RECENT YEARS. ITS SIMPLE COMBINATION OF WHITE CEMENT, WHITE MARBLE AGGREGATE AND WATER MAKE FOR AN ECONOMICAL CHOICE THAT WILL GIVE YOU THAT CLASSIC SWIMMING POOL LOOK. AGGREGATE EFFECTS – COLORED CERAMIC QUARTZ ANOTHER HIGHLY INNOVATIVE ADDITION TO THE PALETTE OF SURFACE OPTIONS HAS BEEN THE USE OF SPECIAL COLORED CERAMIC AGGREGATE PRODUCTS. THESE AGGREGATES ARE BASICALLY A VERY SPECIALIZED FORM OF CERAMIC-COATED SAND THAT COMES IN A VARIETY OF PRE-MIXED PLASTER PRODUCTS. THE EXPOSED AGGREGATE REVOLUTION PERHAPS THE ULTIMATE ANSWER TO ALL POOL SURFACE CONCERNS COMES IN THE FORM OF PEBBLE SURFACES. PEBBLE SURFACES CONSIST OF SMALL, SMOOTH RIVER PEBBLES EMBEDDED THROUGHOUT THE PRODUCT. OVER THE PAST DECADE, PEBBLE SURFACES HAVE INCREASED DRAMATICALLY IN POPULARITY AND COME IN A BROAD RANGE OF COLORS AND COLOR COMBINATIONS.
WHEN HEATING A POOL OR SPA IT IS 67% MORE EFFICIENT TO DELIVER THE HEATED WATER TO THE BOTTOM OF THE WATER'S ENVIRONMENT. THIS IS SUBSTANTIATED IN THE SCIENCE OF HYDRONICS AND SOME OF THE OLDEST EXAMPLES OF THIS ARE STEAM AND HOT WATER RADIATORS. IN PROVIDING A PLUMBING DESIGN THAT TAKES ADVANTAGE OF THIS, THE WATER WILL HEAT UP FASTER AND MORE EFFICIENTLY. HOT WATER RETURNS ARE GENERALLY CONNECTED TO AN AUTOMATED FUNCTION FEATURE THAT CAN ACTIVATE THIS MODE OF OPERATION WHEN IT IS BEING DESIRED. (Click to add description)
INDICATE THE TYPE OF SURFACE THAT IS INTENDED TO SURROUND THE POOL / SPA.
CONCRETE FLAT-WORK IS MEASURED BY SQUARE FEET OF A GIVEN AREA AND THEN TOTALED. SOME CONCRETE FLAT-WORK AREAS MAY NOT BE KNOWN AT THE BEGINNING OF THE DESIGN PROCESS, AS IT GENERALLY IS AN EXTENSION OF THE DESIGN ONLY AFTER A POOL / SPA HAS BEEN POSITIONED IN THE YARD SPACE. IF YOU HAVE AN APPROXIMATION OF SOME AREAS THAT ARE BEING CONSIDERED I.E.; PATIO @ 10' x 10' = 100-SF, WALKWAY @ 3.5' x 50' = 175-SF, ETC.. THEN WE WILL BE ABLE TO APPLY THAT INFORMATION TO DEVELOPING A PLAN THAT MORE CLOSELY PARALLELS YOUR BACKYARD VISION. TELL US WHAT YOU CAN SO THAT WE MAY BECOME MORE AWARE OF YOUR PERSONAL DESIRES.
AB ROCK IMPORT CAN BE USED TO PREPARE THE PAVING AREA'S SUB-GRADE. IN ORDER TO IDENTIFY ALL REQUIREMENTS PLEASE INDICATE HERE WHETHER OR NOT IT SHALL BE YOUR DESIRE TO INCLUDE THIS ELEMENT OF PREPARATION. SPOILS.
IN MANY AREAS THE NATIVE SOIL HAS A HIGH CLAY PERCENTAGE OF ITS CONTENT. CLAY HAS EXPANSIVE CHARACTERISTICS AND THE MORE PERCENTAGE OF CLAY THAT A NATIVE SOIL CONTAINS, GENERALLY THE MORE IT CAN EXPAND. WHEN A HEAVY CLAY SUB-SOIL ABSORBS MOISTURE IT BEGINS TO SWELL. IF THAT SOIL TYPE IS UNDER CONCRETE FLAT-WORK AND IT SWELLS, WELL THEN IT CAN CAUSE A DECK TO BEGIN TO LIFT. MITIGATING THIS POTENTIAL IS OFF-SET WITH PREFORMING PER-SATURATION OF THE SUB-GRADE AND USING A CLASS II COMPACT-ABLE IMPORTED FILL MATERIAL SUCH AS AB-BASE ROCK. GENERALLY SPEAKING AND UNDER SUCH CONDITIONS, 4" TO 6" OF AB IS PLACED UNDER ALL DECKS AND A VIBRATORY COMPACTION PLATE IS USED TO PREPARE THE FLAT-WORK'S SUB-GRADE. KEEPING IN MIND THAT, IF AB IMPORT IS DESIRED, YOU WILL NEED TO ACCOUNT FOR THE REMOVAL OF 4" TO 6" OF NATIVE SOIL AND HAUL-OFF. THIS IS REFERRED TO AS THE REMOVAL OF SPOILS.
A VIBRATORY COMPACTION PLATE CAN BE USED TO PREPARE THE PAVING AREA'S SUB-GRADE. IN ORDER TO IDENTIFY ALL REQUIREMENTS PLEASE INDICATE HERE WHETHER OR NOT IT SHALL BE YOUR DESIRE TO INCLUDE THIS ELEMENT OF PREPARATION.
AB IS PLACED UNDER ALL DECKS AND A VIBRATORY COMPACTION PLATE IS USED TO PREPARE THE FLAT-WORK'S SUB-GRADE. KEEPING IN MIND THAT, IF AB IMPORT IS DESIRED, YOU WILL NEED TO ACCOUNT FOR THE REMOVAL OF 4" TO 6" OF NATIVE SOIL AND HAUL-OFF. THIS IS REFERRED TO AS THE REMOVAL OF SPOILS.
OUR RECOMMENDATION IS TO USE #3 @ 18" x 18" O.C.B.W. THROUGHOUT ALL CONCRETE FLAT-WORK AREAS.
EQUIPOTENTIAL BONDING CODE (NEC. 680) REQUIRES A MIN. OF 18" X 18" O.C.B.W. #3 STEEL REINFORCEMENTS TO BE PLACED IN A CONCRETE DECK FOR A MIN. OF 3'-0" AROUND THE ENTIRE SWIMMING POOL / SPA PERIMETER. OUR RECOMMENDATION IS TO USE #3 @ 18" x 18" O.C.B.W. THROUGHOUT ALL CONCRETE FLAT-WORK AREAS.
THERE ARE MANY ATTAINABLE POSSIBILITIES IN SEEKING GREAT RESULTS BUT, GREAT RESULTS START WITH GREAT PLANNING. WE SUGGEST THAT YOU START BY CLEARLY DEFINING THE APPROACH, AND FROM THESE EFFORTS YOUR EXPECTATIONS SHALL BECOME ANCHORED IN A DESCRIPTIVE MEANING FOR HOW THAT REALITY WILL APPEAR. WITH CONCRETE FLAT-WORK, THIS BEGINS BY DEVELOPING AN EASY TO FOLLOW “SPECIFICATION”, THAT SHALL LIST MOST ALL OF THE CHOICES THAT WILL INVOLVE PROVING YOU WITH A DETAILED COST ESTIMATE RESPONSE FROM CONTENDING PERFORMERS. THIS QUESTIONER WAS DEVELOPED IN ORDER TO PROVIDE YOU WITH A TOOL. IN ENGAGING THIS FRAMEWORK YOU'LL BE PUTTING FORTH AN EFFORT TO ASSIST US IN COLLABORATING THAT INFORMATION INTO A REFINING AND DEFINING PRESCRIPTION FOR HOW 1ST CLASS RESULTS CAN BE ACHIEVED.
THE SPECIFICATION FOR THE THICKNESS OF THE FLAT-WORK (SLAB ) IS DEFINED BY THE PURPOSE OF THE SLAB. AS AN EXAMPLE; A DRIVEWAY MAY BE REQUIRED TO BE THICKER (ESPECIALLY AT THE STREET APRON WHERE HEAVY TRUCKS CAN OFTEN USE IT AS A TURN-A-ROUND) DEPENDING UPON THE ANTICIPATED VEHICLE TRAFFIC AND VEHICLE WEIGHT A GREATER THICKNESS MAY BE REQUIRED.
CONCRETE COLOR IS EITHER ADDED DURING THE READY MIX PRODUCTION PROCESS OR IT IS DUSTED ON DURING THE CONCRETE FINISHING PROCESS. THE DUST-ON COLOR GENERALLY HAS GREATER LONGEVITY IN RETAINING THE ORIGINAL COLOR VERSES THE IN-LOAD OR INTEGRAL PROCESS.
INDICATE IF THERE IS A DESIRED HEIGHT FOR THE STEP RISER. THE MAX RISER HEIGHT PER CODE IS 7-5/8", ALSO INDICATE THE WIDTH OF THE STEP'S TREAD. THE MINIMUM TREAD PER CODE IS 11"
THE FACING OF THE STAIRS SHOULD BE IDENTIFIED AS TO YOUR DESIRES. THESE ARE SOME OF THOSE OPTIONS THAT CAN BE CALLED OUT ON PLAN.
THERE ARE SEVERAL POOL / SPA EDGE SELECTION OPTIONS FROM WHICH TO CHOOSE AND BY IDENTIFYING YOUR DESIRES IT SHALL ALLOW YOUR PLANS TO PRESCRIBE THE SELECTION THAT SHALL MEET YOUR EXPECTATIONS.
WHEN FORMING, PLACING AND POURING CONCRETE READY MIX AN "ECONOMY IN SCALE" CAN BENEFIT YOU DUE TO THE PERFORMERS GAINING FROM PRODUCTION EFFICIENCIES. THEREFORE, IF CONCRETE MOW-STRIPS, SEATING WALLS, STAIR CASES AND OR OTHER CONCRETE WORKS ARE BEING CONSIDERED, THEN NOTE THESE HERE FOR CONSIDERATION.
SELECT THE TOPICAL APPLICATIONS FOR ANY WALLS, SEATING BENCHES OR OTHER VERTICAL FACING SURFACING
THE TERM "BOND BEAM" REFERS TO THE TOP PORTION OF THE POOL / SPA'S SHELL, WHICH FOLLOWS THE COMPLETE PERIMETER. A "RAISED BOND BEAM" REFERS TO THE PORTION OF THE PERIMETER THAT HAS AN INCREASE IN HEIGHT. HEIGHT INCREASES WILL GENERALLY RISE BY INCREMENTS OF +6" AS A DIMENSION OF +6", +12", +18", +24" AND SO ON. EACH SECTION (A, B, C) WILL NEED A MEASUREMENT FOR THE LENGTH AND HEIGHT RELATIONSHIPS BEING DESIRED. PLEASE PROVIDE A ESTIMATED MEASUREMENT IF APPLICABLE.
PLEASE PROVIDE A ESTIMATED MEASUREMENT IF APPLICABLE.
PLEASE PROVIDE A ESTIMATED MEASUREMENT IF APPLICABLE.
"FROST PROOF" PORCELAIN TILE IS MOST OFTEN USED FOR SWIMMING POOLS. PRODUCT SELECTIONS RANGE IN COSTS BY GROUPINGS (A,B,C,D,E,..ETC.) TYPICALLY THE GROUP "A" IS THE LEAST EXPENSIVE AND THE PURCHASE PRICE SHALL GO UP FROM THERE. THE ACTUAL PRODUCT SELECTION CAN BE MADE ANY TIME PRIOR TO THE INSTALLATION BUT, IT IS IMPORTANT TO DEFINE THE TILE SIZE I.E.; 1" x 1", 2" x 2", 3" x 3", 4" x 4", 6" x 6", ETC...AS THE POOL'S CONFORMITY MUST BE CONSTRUCTED IN ORDER TO MATCH THE SELECTED PRODUCT'S DIMENSIONAL SIZES THAT ARE AVAILABLE.
GROUP "A" IS THE LEAST EXPENSIVE AND THE PURCHASE PRICE SHALL GO UP FROM THERE. THE ACTUAL PRODUCT SELECTION CAN BE MADE ANY TIME PRIOR TO THE INSTALLATION BUT, IT IS IMPORTANT TO DEFINE THE TILE SIZE I.E.; 1" x 1", 2" x 2", 3" x 3", 4" x 4", 6" x 6", ETC...AS THE POOL'S CONFORMITY MUST BE CONSTRUCTED IN ORDER TO MATCH THE SELECTED PRODUCT'S DIMENSIONAL SIZES THAT ARE AVAILABLE.
GROUP "A" IS THE LEAST EXPENSIVE AND THE PURCHASE PRICE SHALL GO UP FROM THERE. THE ACTUAL PRODUCT SELECTION CAN BE MADE ANY TIME PRIOR TO THE INSTALLATION BUT, IT IS IMPORTANT TO DEFINE THE TILE SIZE I.E.; 1" x 1", 2" x 2", 3" x 3", 4" x 4", 6" x 6", ETC...AS THE POOL'S CONFORMITY MUST BE CONSTRUCTED IN ORDER TO MATCH THE SELECTED PRODUCT'S DIMENSIONAL SIZES THAT ARE AVAILABLE.
GROUP "A" IS THE LEAST EXPENSIVE AND THE PURCHASE PRICE SHALL GO UP FROM THERE. THE ACTUAL PRODUCT SELECTION CAN BE MADE ANY TIME PRIOR TO THE INSTALLATION BUT, IT IS IMPORTANT TO DEFINE THE TILE SIZE I.E.; 1" x 1", 2" x 2", 3" x 3", 4" x 4", 6" x 6", ETC...AS THE POOL'S CONFORMITY MUST BE CONSTRUCTED IN ORDER TO MATCH THE SELECTED PRODUCT'S DIMENSIONAL SIZES THAT ARE AVAILABLE.
GROUP "A" IS THE LEAST EXPENSIVE AND THE PURCHASE PRICE SHALL GO UP FROM THERE. THE ACTUAL PRODUCT SELECTION CAN BE MADE ANY TIME PRIOR TO THE INSTALLATION BUT, IT IS IMPORTANT TO DEFINE THE TILE SIZE I.E.; 1" x 1", 2" x 2", 3" x 3", 4" x 4", 6" x 6", ETC...AS THE POOL'S CONFORMITY MUST BE CONSTRUCTED IN ORDER TO MATCH THE SELECTED PRODUCT'S DIMENSIONAL SIZES THAT ARE AVAILABLE.
THIS IS AN IMPORTANT FACTOR TO BE AWARE OF BECAUSE THE WATER ENVIRONMENT MUST MAINTAIN CLEARANCES FROM AN OVERHEAD ELECTRIC SERVICE PER THE NATIONAL ELECTRICAL CODE (NEC) 680.0.
INDICATE ON YOUR ROUGH SKETCH WHERE THE MAIN ELECTRICAL PANEL IS LOCATED AND WHERE YOU WISH THE POOL EQUIPMENT'S SUB-PANEL TO BE LOCATED. PROVIDE AN ESTIMATED DISTANCE (WE WILL VERIFY AFTER THE DIMENSIONAL SITE PLAN HAS BEEN COMPLETED). THE DISTANCE TOGETHER WITH THE AMPERE LOAD DEMAND WILL DETERMINE WHAT THE WIRE AND CONDUIT SIZE WILL NEED TO BE .
THE VOLTAGE WILL MOST OFTEN BE 240v SINGLE PHASE AND THE AMPERE LOAD IS DETERMINED BY THE SELECTED OF THE EQUIPMENT AND EACH OF THE COMPONENT'S ENERGY DEMANDS. THE DISTANCE TOGETHER WITH THE AMPERE LOAD DEMAND WILL DETERMINE WHAT THE WIRE AND CONDUIT SIZE WILL NEED BE AND THIS ALL NEEDS TO FALL WITHIN THE "ALLOWABLE VOLTAGE LOSS", WHICH IS LESS THAN 3.0% WHEN UNDER FOLL LOAD. NO NEED TO FILL THIS IN JUST YET, WE'RE JUST MAKING YOU FAMILIAR WITH HOW THE PROCESS FOR DETERMINING THE CORRECT SIZES IS ACCOMPLISHED.
INDICATE WHAT TYPE OF GAS IS AVAILABLE, IF GAS IS TO BE DISTRIBUTED ON SITE.
PROVIDE A PRELIMINARY DISTANCE FROM THE GAS METER OR TANK TO THE POOL EQUIPMENT PAD, IF KNOWN. THE FINAL VALUE WILL BE DETERMINED FROM THE DIMENSIONS ON THE SITE PLAN.
IN THE CHANCE THAT YOU HAVE OTHER CONSIDERATIONS THAT WE HAVE FAILED TO IDENTIFY, PLEASE PROVIDE US WITH A DESCRIPTION FOR WHAT THESE MAY BE.
IN ACCOMMODATING AN FASTER TURNAROUND TIME-FRAME RESPONSE, IT WILL REQUIRE APPLYING AN O.T. RATE DUE TO THE ADDITIONAL HOURS THAT WILL BE NECESSARY THAT ARE BEYOND THE NORMAL WORK DAY / WEEK.
PLEASE SELECT THE FORM OF PAYMENT YOU'D PREFER. REMEMBER CREDIT CARDS AND PAYPAL HAVE A TRANSACTION FEE THAT WILL BE PART OF THE COSTS WE CHARGE YOU ALSO.
IN PRODUCING A DESIGN FOR OUR CLIENTS, WE MUST REMAIN COGNIZANT OF THEIR BUDGETARY EXPECTATIONS. IT DOES NEITHER OF US ANY GOOD TO END UP DESIGNING SOMETHING THAT TURNS OUT TO BE ECONOMICALLY INFEASIBLE, CORRECT? SO...JUST LIKE WHEN YOU'RE BUYING A HOUSE, THINK OF THE BACKYARD AS A PIECE OF A HOUSE AND YOU KNOW WHAT SIZE HOUSE IS AFFORDABLE. SO SET THE BUDGET AND LEAVE ABOUT +/-10% MORE FOR UPGRADE CONSIDERATIONS.
Sending

Go To Top »
Aquatic Mechanical Engineering (800) 766-5259